VE7SML-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VE7SML-4. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Voltage*	Solar *	temp*
1772689766	13 volts	0.02 amps	2 deg C
1772689466	13 volts	0.02 amps	2 deg C
1772689166	13 volts	0.02 amps	2 deg C
1772688866	13 volts	0.02 amps	2 deg C
1772688566	13 volts	0.02 amps	2 deg C
1772688266	13 volts	0.02 amps	2 deg C
1772687966	13 volts	0.02 amps	2 deg C
1772687666	13 volts	0.02 amps	2 deg C
1772687366	13 volts	0.02 amps	2 deg C
1772687066	13 volts	0.02 amps	2 deg C
1772686766	13 volts	0.02 amps	2 deg C
1772686466	13 volts	0.02 amps	2 deg C
1772686166	13 volts	0.02 amps	2 deg C
1772685866	13 volts	0.02 amps	2 deg C
1772685566	13 volts	0.02 amps	2 deg C
1772685266	13 volts	0.02 amps	2.5 deg C
1772684966	13 volts	0.02 amps	2.5 deg C
1772684666	13 volts	0.02 amps	2.5 deg C
1772684366	13 volts	0.02 amps	2.5 deg C
1772684066	13 volts	0.02 amps	2.5 deg C
1772683771	13 volts	0.02 amps	2.5 deg C
1772683466	13 volts	0.02 amps	3 deg C
1772683166	13 volts	0.02 amps	3 deg C
1772682866	13 volts	0.02 amps	3 deg C
1772682566	13 volts	0.02 amps	3 deg C

*Used Equation Coefficients:

Voltage: 0, 0.075, 3.55

Solar : 0, 0.195, -24.94

temp: 0, 0.5, -64

Value4: 0, 0, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)