W0ARP-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W0ARP-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx1h*	Rx10m*	Eff1h*	Value4*	Vin*
1765757356	0 Pkts	0 Pkts	0 Pcnt	0	12.6 Volts
1765757056	0 Pkts	0 Pkts	0 Pcnt	0	12.53 Volts
1765756756	0 Pkts	0 Pkts	0 Pcnt	0	12.53 Volts
1765756456	0 Pkts	0 Pkts	0 Pcnt	0	12.6 Volts
1765756156	0 Pkts	0 Pkts	0 Pcnt	0	12.53 Volts
1765755868	0 Pkts	0 Pkts	0 Pcnt	0	12.53 Volts
1765755556	0 Pkts	0 Pkts	0 Pcnt	0	12.53 Volts
1765755256	0 Pkts	0 Pkts	0 Pcnt	0	12.6 Volts
1765754956	0 Pkts	0 Pkts	0 Pcnt	0	12.6 Volts
1765754656	0 Pkts	0 Pkts	0 Pcnt	0	12.53 Volts
1765754356	0 Pkts	0 Pkts	0 Pcnt	0	12.53 Volts
1765754056	0 Pkts	0 Pkts	0 Pcnt	0	12.53 Volts
1765753756	0 Pkts	0 Pkts	0 Pcnt	0	12.53 Volts
1765753456	0 Pkts	0 Pkts	0 Pcnt	0	12.53 Volts
1765753156	0 Pkts	0 Pkts	0 Pcnt	0	12.53 Volts
1765752856	0 Pkts	0 Pkts	0 Pcnt	0	12.53 Volts
1765752556	0 Pkts	0 Pkts	0 Pcnt	0	12.53 Volts
1765752256	0 Pkts	0 Pkts	0 Pcnt	0	12.53 Volts
1765751956	0 Pkts	0 Pkts	0 Pcnt	0	12.53 Volts
1765751656	0 Pkts	0 Pkts	0 Pcnt	0	12.6 Volts
1765751356	0 Pkts	0 Pkts	0 Pcnt	0	12.53 Volts
1765751056	0 Pkts	0 Pkts	0 Pcnt	0	12.53 Volts
1765750756	0 Pkts	0 Pkts	0 Pcnt	0	12.53 Volts
1765750456	0 Pkts	0 Pkts	0 Pcnt	0	12.53 Volts
1765750156	0 Pkts	0 Pkts	0 Pcnt	0	12.6 Volts

*Used Equation Coefficients:

Rx1h: 0, 10, 0

Rx10m: 0, 1, 0

Eff1h: 0, 1, 0

Value4: 0, 0, 0

Vin: 0, 0.075, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)