YB9VP-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YB9VP-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*	V_Bat*	V_Ext*
1772699938	0 Count	0 Count	0 Count	0 VDC	0 VDC
1772698134	0 Count	0 Count	0 Count	0 VDC	0 VDC
1772696334	0 Count	0 Count	0 Count	0 VDC	0 VDC
1772694534	0 Count	0 Count	0 Count	0 VDC	0 VDC
1772692744	0 Count	0 Count	0 Count	0 VDC	0 VDC
1772690934	0 Count	0 Count	0 Count	0 VDC	0 VDC
1772689134	0 Count	0 Count	0 Count	0 VDC	0 VDC
1772687334	0 Count	0 Count	0 Count	0 VDC	0 VDC
1772685534	0 Count	0 Count	0 Count	0 VDC	0 VDC
1772683733	0 Count	0 Count	0 Count	0 VDC	0 VDC
1772681937	0 Count	0 Count	0 Count	0 VDC	0 VDC
1772680138	0 Count	0 Count	0 Count	0 VDC	0 VDC
1772678336	0 Count	0 Count	0 Count	0 VDC	0 VDC
1772676536	0 Count	0 Count	0 Count	0 VDC	0 VDC
1772674736	0 Count	0 Count	0 Count	0 VDC	0 VDC
1772672935	0 Count	0 Count	0 Count	0 VDC	0 VDC
1772671135	0 Count	0 Count	0 Count	0 VDC	0 VDC
1772669335	0 Count	0 Count	0 Count	0 VDC	0 VDC
1772667535	0 Count	0 Count	0 Count	0 VDC	0 VDC
1772665747	0 Count	0 Count	0 Count	0 VDC	0 VDC
1772663931	0 Count	0 Count	0 Count	0 VDC	0 VDC
1772662131	0 Count	0 Count	0 Count	0 VDC	0 VDC
1772660331	0 Count	0 Count	0 Count	0 VDC	0 VDC
1772658531	0 Count	0 Count	0 Count	0 VDC	0 VDC
1772656731	0 Count	0 Count	0 Count	0 VDC	0 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)