BX6AM-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BX6AM-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1787577745	43 C	19 p	58 p	1334 p
1787576545	42.8 C	19 p	63 p	1332 p
1787575346	43.4 C	20 p	61 p	1326 p
1787574146	42.2 C	24 p	62 p	1322 p
1787572946	43.5 C	17 p	56 p	1313 p
1787571746	43.7 C	21 p	58 p	1315 p
1787570546	43.1 C	18 p	59 p	1316 p
1787569345	42.9 C	19 p	56 p	1315 p
1787568145	42.8 C	22 p	54 p	1313 p
1787566945	43.5 C	15 p	51 p	1312 p
1787565745	42.6 C	17 p	54 p	1315 p
1787564546	43.2 C	19 p	56 p	1316 p
1787563346	43.6 C	18 p	84 p	1316 p
1787562146	43.9 C	19 p	83 p	1315 p
1787560946	43 C	47 p	81 p	1315 p
1787559746	43.4 C	17 p	49 p	1288 p
1787558546	43.7 C	17 p	48 p	1288 p
1787557346	43.2 C	15 p	49 p	1287 p
1787556146	43.6 C	16 p	49 p	1290 p
1787554946	43.7 C	18 p	50 p	1293 p
1787553746	42.4 C	15 p	45 p	1289 p
1787552546	43.1 C	17 p	51 p	1287 p
1787551346	42.9 C	13 p	51 p	1286 p
1787550146	43 C	21 p	55 p	1302 p
1787548946	43.1 C	17 p	56 p	1300 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)