YD1AFF-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YD1AFF-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temperatu*	Humidity*	Pressure*
1789963149	41 °C	26 %RH	1010 hPa
1789961249	40 °C	26 %RH	1011 hPa
1789959349	40 °C	28 %RH	1012 hPa
1789957449	39 °C	31 %RH	1012 hPa
1789955549	39 °C	33 %RH	1012 hPa
1789954891	38 °C	33 %RH	1012 hPa
1789952991	38 °C	39 %RH	1012 hPa
1789951091	35 °C	43 %RH	1011 hPa
1789949191	32 °C	45 %RH	1011 hPa
1789947291	30 °C	49 %RH	1011 hPa
1789945391	29 °C	52 %RH	1010 hPa
1789943490	29 °C	51 %RH	1010 hPa
1789941590	29 °C	51 %RH	1010 hPa
1789939690	30 °C	50 %RH	1010 hPa
1789937790	30 °C	56 %RH	1010 hPa
1789935890	30 °C	59 %RH	1010 hPa
1789933990	30 °C	59 %RH	1010 hPa
1789932090	30 °C	59 %RH	1010 hPa
1789930190	31 °C	57 %RH	1010 hPa
1789928290	31 °C	58 %RH	1010 hPa
1789926390	31 °C	57 %RH	1010 hPa
1789924490	31 °C	58 %RH	1011 hPa
1789922590	31 °C	58 %RH	1011 hPa
1789920690	31 °C	58 %RH	1012 hPa
1789918789	31 °C	57 %RH	1012 hPa

*Used Equation Coefficients:

Temperatu: 0, 1, 0

Humidity: 0, 1, 0

Pressure: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)