YE2YE-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YE2YE-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Temp.*	Humidity*	Pressure*
1777946960	29 °C	64 %RH	1001 hPa
1777945960	30 °C	65 %RH	1001 hPa
1777944960	29 °C	65 %RH	1001 hPa
1777943960	29 °C	66 %RH	1001 hPa
1777942960	30 °C	63 %RH	1000 hPa
1777941960	29 °C	65 %RH	1000 hPa
1777940960	29 °C	65 %RH	1000 hPa
1777939960	29 °C	63 %RH	1000 hPa
1777938960	29 °C	63 %RH	1000 hPa
1777937960	28 °C	67 %RH	1000 hPa
1777914399	26 °C	44 %RH	1000 hPa
1777913399	26 °C	44 %RH	1000 hPa
1777912399	26 °C	45 %RH	1000 hPa
1777911399	26 °C	45 %RH	1000 hPa
1777910399	26 °C	45 %RH	1001 hPa
1777909399	26 °C	45 %RH	1001 hPa
1777908399	26 °C	45 %RH	1001 hPa
1777907399	26 °C	46 %RH	1001 hPa
1777906399	26 °C	46 %RH	1001 hPa
1777905399	25 °C	51 %RH	1001 hPa
1777904871	25 °C	51 %RH	1001 hPa
1777904851	25 °C	51 %RH	1001 hPa
1777904574	25 °C	52 %RH	1001 hPa
1777904540	25 °C	52 %RH	1001 hPa
1777903309	26 °C	50 %RH	1001 hPa

*Used Equation Coefficients:

Temp.: 0, 1, 0

Humidity: 0, 1, 0

Pressure: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)