DA2AC-99 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DA2AC-99. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Temp.in*	Hum*	Temp.out*
1773315096	22.6 C deg	59.9 %	0 C deg
1773304291	23.8 C deg	57.6 %	0 C deg
1773304285	23.8 C deg	57.6 %	0 C deg
1773293484	22.2 C deg	60.6 %	0 C deg
1773293484	22.2 C deg	60.6 %	0 C deg
1773286292	22.3 C deg	60.4 %	0 C deg
1773277302	22.5 C deg	60.6 %	0 C deg
1773277291	22.5 C deg	60.6 %	0 C deg
1773271889	22.2 C deg	60.6 %	0 C deg
1773271889	22.2 C deg	60.6 %	0 C deg
1773270084	22.3 C deg	60.5 %	0 C deg
1773270084	22.3 C deg	60.5 %	0 C deg
1773264695	22.6 C deg	59.7 %	0 C deg
1773264684	22.6 C deg	59.7 %	0 C deg
1773255689	22.4 C deg	59.8 %	0 C deg
1773225102	22.4 C deg	58.3 %	0 C deg
1773223294	22.4 C deg	58.3 %	0 C deg
1773223288	22.4 C deg	58.3 %	0 C deg
1773221488	22.3 C deg	58.1 %	0 C deg
1773207111	22.7 C deg	60.5 %	0 C deg
1773207096	22.7 C deg	60.5 %	0 C deg
1773190894	24.1 C deg	58.5 %	0 C deg
1773190894	24.1 C deg	58.5 %	0 C deg
1773181901	24 C deg	58.7 %	0 C deg
1773178295	24.1 C deg	58.4 %	0 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)