SP8EBC-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP8EBC-12. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Vbatt*	Tempre*
1788577837	59 Pkt	12.62 V	0 DegC
1788577237	60 Pkt	12.66 V	0 DegC
1788576628	58 Pkt	12.66 V	0 DegC
1788576030	61 Pkt	12.68 V	0 DegC
1788575417	57 Pkt	10 V	-50 DegC
1788552792	59 Pkt	12.7 V	0 DegC
1788552192	60 Pkt	12.68 V	0 DegC
1788551583	59 Pkt	12.62 V	0 DegC
1788550980	59 Pkt	12.74 V	0 DegC
1788550381	60 Pkt	12.6 V	0 DegC
1788549772	59 Pkt	12.7 V	0 DegC
1788549172	60 Pkt	12.7 V	0 DegC
1788548563	59 Pkt	12.68 V	0 DegC
1788547964	60 Pkt	12.72 V	0 DegC
1788546754	60 Pkt	12.72 V	0 DegC
1788546163	59 Pkt	12.72 V	0 DegC
1788545546	60 Pkt	12.74 V	0 DegC
1788544936	59 Pkt	12.76 V	0 DegC
1788544336	60 Pkt	12.68 V	0 DegC
1788543727	59 Pkt	12.74 V	0 DegC
1788543127	60 Pkt	12.74 V	0 DegC
1788542518	59 Pkt	12.76 V	0 DegC
1788541919	60 Pkt	12.78 V	0 DegC
1788541307	59 Pkt	12.78 V	0 DegC
1788540708	60 Pkt	12.8 V	0 DegC

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Visc10min: 0, 1, 0

Digi10min: 0, 1, 0

Vbatt: 0, 0.02, 10

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)