SADDLE Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SADDLE. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1789945556	14.18 Volt	780 Pkt	40 Pkt	57 Pcnt
1789945546	14.18 Volt	780 Pkt	40 Pkt	57 Pcnt
1789941957	14.18 Volt	810 Pkt	30 Pkt	61 Pcnt
1789941946	14.18 Volt	810 Pkt	30 Pkt	61 Pcnt
1789938351	14.18 Volt	880 Pkt	40 Pkt	62 Pcnt
1789938346	14.18 Volt	880 Pkt	40 Pkt	62 Pcnt
1789934755	14.18 Volt	920 Pkt	40 Pkt	63 Pcnt
1789934746	14.18 Volt	920 Pkt	40 Pkt	63 Pcnt
1789931147	14.18 Volt	920 Pkt	40 Pkt	55 Pcnt
1789931146	14.18 Volt	920 Pkt	40 Pkt	55 Pcnt
1789927554	14.18 Volt	920 Pkt	40 Pkt	59 Pcnt
1789927546	14.18 Volt	920 Pkt	40 Pkt	59 Pcnt
1789923949	14.18 Volt	940 Pkt	30 Pkt	66 Pcnt
1789923947	14.18 Volt	940 Pkt	30 Pkt	66 Pcnt
1789920356	14.18 Volt	810 Pkt	30 Pkt	61 Pcnt
1789920347	14.18 Volt	810 Pkt	30 Pkt	61 Pcnt
1789916749	14.18 Volt	800 Pkt	40 Pkt	62 Pcnt
1789916747	14.18 Volt	800 Pkt	40 Pkt	62 Pcnt
1789913154	14.18 Volt	740 Pkt	20 Pkt	62 Pcnt
1789913147	14.18 Volt	740 Pkt	20 Pkt	62 Pcnt
1789909549	14.18 Volt	710 Pkt	20 Pkt	60 Pcnt
1789909547	14.18 Volt	710 Pkt	20 Pkt	60 Pcnt
1789905961	14.18 Volt	720 Pkt	30 Pkt	66 Pcnt
1789905947	14.18 Volt	720 Pkt	30 Pkt	66 Pcnt
1789902349	13.05 Volt	640 Pkt	30 Pkt	60 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)