KE8ESP-A2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KE8ESP-A2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TEMP*	LOAD*	RAM*	SWAP*	DISK*
1787565608	36 C	1.1 X	12 %	3 %	44 %
1787565307	37 C	0.9 X	12 %	3 %	44 %
1787565008	38 C	1.4 X	12 %	3 %	44 %
1787564708	37 C	1.2 X	13 %	3 %	44 %
1787564408	39 C	1.1 X	13 %	3 %	44 %
1787564108	38 C	0.9 X	12 %	3 %	44 %
1787563808	39 C	1.1 X	12 %	3 %	44 %
1787563508	38 C	1.1 X	12 %	3 %	44 %
1787563208	37 C	0.8 X	12 %	3 %	44 %
1787562908	38 C	0.8 X	12 %	3 %	44 %
1787562608	37 C	1.6 X	12 %	3 %	44 %
1787562308	37 C	1.1 X	13 %	3 %	44 %
1787562008	38 C	1 X	12 %	3 %	44 %
1787561806	38 C	0.7 X	12 %	3 %	44 %
1787561409	38 C	1.2 X	13 %	3 %	44 %
1787561108	37 C	1 X	12 %	3 %	44 %
1787560809	38 C	1.1 X	12 %	3 %	44 %
1787560509	37 C	0.7 X	13 %	3 %	44 %
1787560209	37 C	1 X	12 %	3 %	44 %
1787559909	38 C	0.7 X	13 %	3 %	44 %
1787559609	37 C	0.9 X	12 %	3 %	44 %
1787559309	37 C	1.4 X	12 %	3 %	44 %
1787559009	38 C	1 X	13 %	3 %	44 %
1787558709	38 C	1.6 X	12 %	3 %	44 %
1787558409	39 C	1 X	12 %	3 %	44 %

*Used Equation Coefficients:

TEMP: 0, 1, 0

LOAD: 0, 0.1, 0

RAM: 0, 1, 0

SWAP: 0, 1, 0

DISK: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)