N0JD Telemetry

This is the latest recevied telemetry packets stored in our database for station/object N0JD. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx_10min*	%Drop_10min*	%Direct_10min*
1774131249	68 Pkts	47.06 %	16.18 %
1774130649	58 Pkts	41.38 %	12.07 %
1774130049	77 Pkts	45.45 %	10.39 %
1774129449	67 Pkts	47.76 %	17.91 %
1774128849	63 Pkts	52.38 %	19.05 %
1774128249	92 Pkts	52.17 %	17.39 %
1774127649	122 Pkts	56.56 %	9.84 %
1774127049	113 Pkts	54.87 %	12.39 %
1774126449	125 Pkts	59.25 %	15.69 %
1774125849	131 Pkts	57.25 %	10.69 %
1774125249	160 Pkts	57.5 %	10 %
1774124649	163 Pkts	59.51 %	10.43 %
1774124049	108 Pkts	54.63 %	13.89 %
1774123449	105 Pkts	54.29 %	10.48 %
1774122849	123 Pkts	52.85 %	13.01 %
1774122249	124 Pkts	55.65 %	14.52 %
1774121649	155 Pkts	59.35 %	14.19 %
1774121049	144 Pkts	72.92 %	15.28 %
1774120449	133 Pkts	61.89 %	14.27 %
1774119849	131 Pkts	64.89 %	15.27 %
1774119249	166 Pkts	71.69 %	19.28 %
1774118649	143 Pkts	70.63 %	20.98 %
1774118049	112 Pkts	53.57 %	16.96 %
1774117449	89 Pkts	43.82 %	20.22 %
1774116849	105 Pkts	51.43 %	16.19 %

*Used Equation Coefficients:

Rx_10min: 0, 1, 0

RxSat_10min: 0, 1, 0

%Drop_10min: 0, 1, 0.058824

%Direct_10min: 0, 1, 0.176471

RxAltFreq_10min: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)