DB0GH Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB0GH. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1788666076	14.1 deg C	55 %	1027.7 hPa
1788665176	14.2 deg C	55 %	1027.8 hPa
1788664275	14.4 deg C	54.9 %	1026.7 hPa
1788663375	14.6 deg C	54.9 %	1025.6 hPa
1788662475	14.8 deg C	54.9 %	1027.3 hPa
1788661575	15.1 deg C	54.7 %	1026.3 hPa
1788660675	15.3 deg C	54.6 %	1026.4 hPa
1788659775	15.5 deg C	54.5 %	1024.6 hPa
1788658875	15.8 deg C	54.5 %	1026.1 hPa
1788657975	16 deg C	54.3 %	1025.7 hPa
1788657075	16.2 deg C	54.3 %	1026.4 hPa
1788656175	16.3 deg C	54.4 %	1026 hPa
1788655275	16.5 deg C	54.4 %	1026.2 hPa
1788654374	16.6 deg C	54.4 %	1026.5 hPa
1788653474	16.8 deg C	54.3 %	1026.4 hPa
1788652574	17 deg C	54.3 %	1024 hPa
1788651674	17.2 deg C	54.4 %	1025.8 hPa
1788650774	17.4 deg C	54.3 %	1025.7 hPa
1788649874	17.8 deg C	54 %	1024.3 hPa
1788648974	18.2 deg C	53.8 %	1026.4 hPa
1788648073	18.5 deg C	53.6 %	1025.3 hPa
1788647173	18.6 deg C	53.7 %	1025.4 hPa
1788646273	18.8 deg C	53.6 %	1024.5 hPa
1788645373	19 deg C	53.5 %	1025 hPa
1788644473	19.2 deg C	53.5 %	1024 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)