EA4EUO-7 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object EA4EUO-7. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Celsius*	Rel_Hum*	Atm_Press*
1788551713	30.1 C	24.63 %	1022.63 hPa
1788551536	30.1 C	24.5 %	1022.75 hPa
1788550577	30.9 C	23.1 %	1025.5 hPa
1788550229	31.4 C	23.19 %	1025.25 hPa
1788549815	31.9 C	22.39 %	1026.63 hPa
1788547129	34.8 C	20.24 %	1023.75 hPa
1788502684	31.1 C	21.81 %	1026.25 hPa
1788495447	32.5 C	21.42 %	1027.75 hPa
1788486415	34.5 C	21.86 %	1029.63 hPa
1788468352	36.1 C	22.13 %	1027.13 hPa
1788463951	35.3 C	21.67 %	1025 hPa
1788416486	32 C	21.5 %	1029.13 hPa
1788414758	32.1 C	21.84 %	1028.25 hPa
1788405726	33.9 C	21.08 %	1027 hPa
1788396694	36.4 C	20.41 %	1027 hPa
1788387688	39.4 C	20.33 %	1030.63 hPa
1788378631	43.9 C	19.54 %	1026.63 hPa
1788369598	47.3 C	21.94 %	1025.5 hPa
1788360566	44.3 C	28.37 %	1026.5 hPa
1788355884	35.8 C	23.64 %	1026.13 hPa
1788329963	30.7 C	22.6 %	1030.25 hPa
1788326444	31.2 C	22.26 %	1025.63 hPa
1788317413	33.1 C	22.21 %	1023.88 hPa
1788308380	35.3 C	22.01 %	1023.88 hPa
1788299349	37.9 C	21.87 %	1025 hPa

*Used Equation Coefficients:

Celsius: 0, 0.1, -50

Rel_Hum: 0, 0.01, 0

Atm_Press: 0, 0.125, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)