DL9DAX-25 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DL9DAX-25. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp.in*	Hum*	Temp.out*
1789967932	22.1 C deg	48 %	0 C deg
1789967894	22.1 C deg	48 %	0 C deg
1789966080	22.1 C deg	48 %	0 C deg
1789964248	22.1 C deg	48.1 %	0 C deg
1789960575	22.2 C deg	48.1 %	0 C deg
1789958776	22.2 C deg	48.1 %	0 C deg
1789958745	22.2 C deg	48.1 %	0 C deg
1789956939	22.2 C deg	48.1 %	0 C deg
1789956912	22.2 C deg	48.1 %	0 C deg
1789955095	22.3 C deg	48.1 %	0 C deg
1789953252	22.4 C deg	48 %	0 C deg
1789951458	22.5 C deg	47.9 %	0 C deg
1789951437	22.5 C deg	47.9 %	0 C deg
1789949590	22.4 C deg	48 %	0 C deg
1789945947	22.5 C deg	47.9 %	0 C deg
1789944108	22.6 C deg	47.7 %	0 C deg
1789940441	22.6 C deg	47.9 %	0 C deg
1789938616	22.6 C deg	48.1 %	0 C deg
1789936849	22.7 C deg	47.9 %	0 C deg
1789936817	22.7 C deg	47.9 %	0 C deg
1789933120	22.9 C deg	47.7 %	0 C deg
1789931296	23 C deg	47.6 %	0 C deg
1789927629	23.1 C deg	47.5 %	0 C deg
1789925842	23.1 C deg	47.3 %	0 C deg
1789924004	23.1 C deg	47.8 %	0 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)