KP3M-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KP3M-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	BAT*	PIV*	TMP*	CPT*
1788642117	13.4 V	4.9 V	94 F	115 F
1788638516	13.4 V	4.9 V	95 F	116 F
1788634917	13.4 V	4.9 V	97 F	117 F
1788631317	13.4 V	4.9 V	99 F	119 F
1788624117	14.1 V	4.9 V	98 F	117 F
1788620517	13.6 V	5 V	97 F	118 F
1788616916	13.5 V	5 V	95 F	116 F
1788613316	13.3 V	4.9 V	92 F	112 F
1788609716	13.3 V	4.9 V	94 F	116 F
1788606116	13.2 V	4.9 V	86 F	107 F
1788602516	13.1 V	4.9 V	83 F	105 F
1788598916	13.1 V	4.9 V	84 F	105 F
1788591716	13.2 V	4.9 V	83 F	105 F
1788588116	13.2 V	4.9 V	83 F	105 F
1788584516	13.2 V	4.9 V	84 F	106 F
1788577317	13.2 V	4.9 V	84 F	104 F
1788573716	13.2 V	4.9 V	85 F	105 F
1788566516	13.2 V	4.9 V	87 F	107 F
1788559315	13.3 V	4.9 V	96 F	116 F
1788555716	13.4 V	4.9 V	100 F	120 F
1788552116	13.4 V	4.9 V	97 F	118 F
1788548516	13.4 V	4.9 V	97 F	118 F
1788544916	13.4 V	4.9 V	99 F	120 F
1788541343	14.1 V	4.9 V	99 F	121 F
1788537716	14.1 V	4.9 V	99 F	120 F

*Used Equation Coefficients:

BAT: 0, 0.1, 0

PIV: 0, 0.1, 0

TMP: 0, 1, -40

HUM: 0, 1, 0

CPT: 0, 1, -40

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)