DC5WT-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DC5WT-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1784758751	15.1 deg C	54 %	1018.8 hPa
1784757846	15.4 deg C	53.6 %	1018.8 hPa
1784756946	15.8 deg C	52.9 %	1018.8 hPa
1784756046	16 deg C	52.1 %	1019 hPa
1784755206	16.4 deg C	51.7 %	1019 hPa
1784754246	16.8 deg C	50.8 %	1019.1 hPa
1784753349	17.1 deg C	50.1 %	1019 hPa
1784752446	17.5 deg C	49.7 %	1019 hPa
1784751545	17.9 deg C	48.4 %	1018.9 hPa
1784750648	18.3 deg C	48.1 %	1018.9 hPa
1784749745	18.8 deg C	47 %	1018.8 hPa
1784748851	19.2 deg C	46.4 %	1018.6 hPa
1784747945	19.8 deg C	46.3 %	1018.5 hPa
1784747054	20.3 deg C	44.9 %	1018.4 hPa
1784746145	20.9 deg C	44.1 %	1018.3 hPa
1784745261	21.4 deg C	43.5 %	1018.2 hPa
1784744345	21.8 deg C	43.1 %	1018.2 hPa
1784743467	22.1 deg C	43 %	1018.1 hPa
1784742545	22.7 deg C	42.2 %	1018 hPa
1784741652	23.2 deg C	41.3 %	1018.1 hPa
1784740744	23.1 deg C	40.9 %	1018 hPa
1784739890	24.4 deg C	39.7 %	1018 hPa
1784738944	24.7 deg C	40.8 %	1017.9 hPa
1784738045	24.8 deg C	41 %	1018.1 hPa
1784737144	24.9 deg C	40.5 %	1018 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)