YH3AJS-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YH3AJS-9. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	FLOOD*	Batt*	Panel*
1776491326	203 cm	3.75 V	4.87 V
1776491205	125 cm	0.03 V	13.89 V
1776491085	125 cm	0.2 V	5.82 V
1776491085	125 cm	0.2 V	5.82 V
1776490962	125 cm	3.71 V	10.75 V
1776490725	125 cm	3.88 V	2.91 V
1776490601	125 cm	4.08 V	9.52 V
1776490481	125 cm	3.76 V	3.75 V
1776490239	125 cm	4.17 V	12.66 V
1776490119	125 cm	3.5 V	2.58 V
1776489998	124 cm	0.13 V	10.86 V
1776489635	125 cm	4.04 V	12.94 V
1776489517	125 cm	0.02 V	5.38 V
1776489397	125 cm	0.05 V	6.94 V
1776489274	125 cm	0.08 V	11.87 V
1776489156	125 cm	3.96 V	1.9 V
1776489032	125 cm	4.09 V	12.71 V
1776488915	125 cm	4.16 V	9.35 V
1776488791	125 cm	0.13 V	1.9 V
1776488554	124 cm	0.08 V	7.5 V
1776488431	124 cm	4.13 V	6.72 V
1776488310	124 cm	3.6 V	12.71 V
1776488190	124 cm	4.19 V	12.66 V
1776488070	124 cm	3.61 V	10.75 V
1776487949	124 cm	4.13 V	8.9 V

*Used Equation Coefficients:

FLOOD: 0, 1, 0

Batt: 0, 0.0165, 0

Panel: 0, 0.056, 0

: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)