HS2AC-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS2AC-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TEMP*	HUM*	BAT*
1784740144	32.38 °C	58.4 %RH	3.98 V
1784739544	32.38 °C	58.4 %RH	3.98 V
1784738944	32.38 °C	58.4 %RH	3.98 V
1784738344	32.38 °C	58.4 %RH	3.98 V
1784737744	32.38 °C	58.4 %RH	3.98 V
1784736544	32.38 °C	58.4 %RH	3.98 V
1784735944	32.38 °C	58.4 %RH	3.98 V
1784735344	32.38 °C	58.4 %RH	3.98 V
1784734744	32.38 °C	58.4 %RH	3.98 V
1784734144	32.38 °C	58.4 %RH	3.98 V
1784732944	32.38 °C	58.4 %RH	3.98 V
1784732344	32.38 °C	58.4 %RH	3.98 V
1784731744	32.38 °C	58.4 %RH	3.98 V
1784731144	32.38 °C	58.4 %RH	3.98 V
1784730544	32.38 °C	58.4 %RH	3.98 V
1784729343	32.38 °C	58.4 %RH	3.98 V
1784728743	32.38 °C	58.4 %RH	3.98 V
1784728143	32.38 °C	58.4 %RH	3.98 V
1784727543	32.38 °C	58.4 %RH	3.98 V
1784726943	32.38 °C	58.4 %RH	3.98 V
1784725743	32.38 °C	58.4 %RH	3.98 V
1784725143	32.38 °C	58.4 %RH	3.98 V
1784724543	32.38 °C	58.4 %RH	3.98 V
1784723943	32.38 °C	58.4 %RH	3.98 V
1784723348	32.38 °C	58.4 %RH	3.98 V

*Used Equation Coefficients:

TEMP: 0, 0.01, 0

HUM: 0, 0.1, 0

BAT: 0, 0.01, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)