KK5CM-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KK5CM-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Room*	Battery*	Eff1h*
1788576323	19.5 C	13.5 Volt	100 Pcnt
1788575723	19.5 C	13.5 Volt	100 Pcnt
1788573923	19.5 C	13.5 Volt	100 Pcnt
1788573323	19.5 C	13.5 Volt	100 Pcnt
1788572723	19.5 C	13.5 Volt	100 Pcnt
1788572123	19.5 C	13.5 Volt	100 Pcnt
1788571523	19.5 C	13.5 Volt	100 Pcnt
1788570923	19.5 C	13.5 Volt	100 Pcnt
1788570323	19.5 C	13.5 Volt	100 Pcnt
1788569723	20 C	13.5 Volt	100 Pcnt
1788569123	19.5 C	13.5 Volt	100 Pcnt
1788568523	19.5 C	13.5 Volt	100 Pcnt
1788567923	20 C	13.5 Volt	100 Pcnt
1788566723	20 C	13.5 Volt	100 Pcnt
1788566123	20 C	13.5 Volt	100 Pcnt
1788565523	20 C	13.5 Volt	100 Pcnt
1788564923	20 C	13.5 Volt	100 Pcnt
1788564323	20 C	13.5 Volt	100 Pcnt
1788563723	20 C	13.5 Volt	100 Pcnt
1788563123	20 C	13.5 Volt	100 Pcnt
1788562523	20 C	13.5 Volt	100 Pcnt
1788561923	20.5 C	13.5 Volt	100 Pcnt
1788561323	20.5 C	13.5 Volt	100 Pcnt
1788560723	20.5 C	13.5 Volt	100 Pcnt
1788560123	21 C	13.5 Volt	100 Pcnt

*Used Equation Coefficients:

Room: 0, 0.5, -64

Battery: 0, 0.075, 0

Eff1h: 0, 1, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)