IR3EO-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IR3EO-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1784650687	12.4 Volt	0 Pkt	61 Pcnt
1784650387	12.4 Volt	0 Pkt	61 Pcnt
1784650087	12.4 Volt	0 Pkt	61 Pcnt
1784649786	12.4 Volt	0 Pkt	61 Pcnt
1784649486	12.4 Volt	0 Pkt	61 Pcnt
1784649186	12.4 Volt	0 Pkt	61 Pcnt
1784648886	12.4 Volt	0 Pkt	61 Pcnt
1784648585	12.4 Volt	0 Pkt	61 Pcnt
1784648285	12.4 Volt	0 Pkt	62 Pcnt
1784647985	12.4 Volt	10 Pkt	62 Pcnt
1784647684	12.4 Volt	10 Pkt	62 Pcnt
1784647384	12.4 Volt	10 Pkt	62 Pcnt
1784647084	12.4 Volt	20 Pkt	62 Pcnt
1784646784	12.4 Volt	20 Pkt	62 Pcnt
1784646483	12.4 Volt	10 Pkt	61 Pcnt
1784646183	12.4 Volt	0 Pkt	61 Pcnt
1784645883	12.4 Volt	0 Pkt	61 Pcnt
1784645582	12.4 Volt	10 Pkt	61 Pcnt
1784645282	12.48 Volt	20 Pkt	61 Pcnt
1784644982	12.4 Volt	20 Pkt	61 Pcnt
1784644682	12.4 Volt	10 Pkt	61 Pcnt
1784644381	12.4 Volt	20 Pkt	61 Pcnt
1784644081	12.4 Volt	20 Pkt	61 Pcnt
1784643781	12.4 Volt	10 Pkt	61 Pcnt
1784643480	12.4 Volt	20 Pkt	61 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)