Dl4HEL-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object Dl4HEL-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	ATemp*	AHum*	vRate*	Sats*	Alt*
1776630371	25.8	42.9	0	6	67.5
1776630065	26.5	39.6	0	0	0
1776629906	28.1	37.2	0	0	0
1776629796	27.3	38.7	0.1	6	76.4
1776629483	30.1	34.1	0	5	0
1776628637	26.9	39.9	0	4	56.5
1776628483	26.3	42.2	0	3	0
1776584312	23.8	43.6	0	0	0
1776550430	27.1	35.2	-0.5	7	6.3
1776550277	26.8	36.1	0	9	75.2
1776550045	26.7	35.7	0.1	11	75.8
1776548492	25.6	38.5	0	0	0
1776548413	25.8	37.5	0	0	0
1776548333	26.6	35.7	0	0	0
1776531718	20.7	37.8	0	8	77.4
1776530494	22	33	0	7	75.3
1776530188	21.9	33.4	0	7	75
1776529881	22.5	31.2	0.1	8	85.8
1776527437	24	27.9	0	7	83.8
1776527127	23.4	28.3	0	10	77.8
1776526973	23.6	27.6	-0.1	9	76.9
1776525303	26.1	32.6	0	0	0
1776257148	29.6	17.6	0.1	10	70.7
1776256841	31.6	17.3	0	11	81.1
1776256382	29.3	17.9	0	11	65.5

*Used Equation Coefficients:

ATemp: 0, 1, 0

AHum: 0, 1, 0

vRate: 0, 1, 0

Sats: 0, 1, 0

Alt: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)