This is the latest recevied telemetry packets stored in our database for station/object OE3EFR-01. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
Press*
Temp.in*
Hum*
QNH*
Temp.out*
1777977176
980 hPa
26.9 C deg
34 %
0 hPa
0 C deg
1777975373
980.4 hPa
25.8 C deg
35.1 %
0 hPa
0 C deg
1777966319
981.5 hPa
22.4 C deg
40.7 %
0 hPa
0 C deg
1777955394
981.5 hPa
13.4 C deg
54.8 %
0 hPa
0 C deg
1777948137
981.8 hPa
14 C deg
50.5 %
0 hPa
0 C deg
1777946316
982 hPa
14.4 C deg
49 %
0 hPa
0 C deg
1777942689
982.3 hPa
15.8 C deg
46.2 %
0 hPa
0 C deg
1777940875
982.3 hPa
16.5 C deg
44.9 %
0 hPa
0 C deg
1777939056
982.3 hPa
17.2 C deg
43.8 %
0 hPa
0 C deg
1777937244
982.5 hPa
17.8 C deg
43.7 %
0 hPa
0 C deg
1777933614
982.8 hPa
18.9 C deg
38.5 %
0 hPa
0 C deg
1777924537
982.7 hPa
22.5 C deg
31.5 %
0 hPa
0 C deg
1777922723
982.7 hPa
23.2 C deg
29.6 %
0 hPa
0 C deg
1777920906
982.9 hPa
23.9 C deg
28.2 %
0 hPa
0 C deg
1777915467
983.1 hPa
26.9 C deg
25.6 %
0 hPa
0 C deg
1777913644
983.2 hPa
28.2 C deg
24.6 %
0 hPa
0 C deg
1777911832
983.2 hPa
30 C deg
22.6 %
0 hPa
0 C deg
1777908205
983.5 hPa
32.4 C deg
20.8 %
0 hPa
0 C deg
*Used Equation Coefficients:
Press: 0, 1, 0
Temp.in: 0, 1, 0
Hum: 0, 1, 0
QNH: 0, 1, 0
Temp.out: 0, 1, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)