DF5RJ-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DF5RJ-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1788512161	23.5 deg C	58.9 %	1015.5 hPa
1788511261	22.6 deg C	61.6 %	1015.8 hPa
1788510361	21.7 deg C	63.5 %	1016.2 hPa
1788509461	22.6 deg C	60.8 %	1016.1 hPa
1788509132	22.5 deg C	60.2 %	1016.1 hPa
1788508232	21.7 deg C	63.8 %	1016.3 hPa
1788507332	19.8 deg C	68 %	1016.8 hPa
1788506432	19.2 deg C	70.9 %	1017 hPa
1788505531	18.9 deg C	71.7 %	1017.1 hPa
1788504631	18.3 deg C	72.3 %	1017.2 hPa
1788503731	18.4 deg C	70.6 %	1017.2 hPa
1788502831	18.5 deg C	70.1 %	1017.1 hPa
1788501931	18.1 deg C	71.4 %	1017.2 hPa
1788501031	16.9 deg C	75.2 %	1017.4 hPa
1788500131	16.3 deg C	77 %	1017.5 hPa
1788499230	16.1 deg C	77.4 %	1017.7 hPa
1788498330	15.3 deg C	80.1 %	1017.8 hPa
1788497430	14.8 deg C	81.5 %	1017.9 hPa
1788497097	14.7 deg C	82.4 %	1018 hPa
1788496197	14.6 deg C	82.9 %	1018.1 hPa
1788495297	14.4 deg C	83 %	1018 hPa
1788494397	14.3 deg C	83.7 %	1018.1 hPa
1788493497	14.2 deg C	83.7 %	1018.3 hPa
1788492597	14.2 deg C	83.5 %	1018.4 hPa
1788491697	14.1 deg C	84.3 %	1018.6 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)