This is the latest recevied telemetry packets stored in our database for station/object SQ9SXN-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
TX*
RX*
Digi*
V_Bat*
V_Ext*
1776739152
21 Count
0 Count
0 Count
0 VDC
0 VDC
1776737351
19 Count
0 Count
0 Count
0 VDC
0 VDC
1776735551
18 Count
0 Count
0 Count
0 VDC
0 VDC
1776733750
16 Count
0 Count
0 Count
0 VDC
0 VDC
1776731949
15 Count
0 Count
0 Count
0 VDC
0 VDC
1776730147
13 Count
0 Count
0 Count
0 VDC
0 VDC
1776728347
12 Count
0 Count
0 Count
0 VDC
0 VDC
1776726546
10 Count
0 Count
0 Count
0 VDC
0 VDC
1776726031
9 Count
0 Count
0 Count
0 VDC
0 VDC
1776726027
8 Count
0 Count
0 Count
0 VDC
0 VDC
1776726010
7 Count
0 Count
0 Count
0 VDC
0 VDC
1776725712
6 Count
0 Count
0 Count
0 VDC
0 VDC
1776725706
5 Count
0 Count
0 Count
0 VDC
0 VDC
1776725638
4 Count
0 Count
0 Count
0 VDC
0 VDC
1776725595
3 Count
0 Count
0 Count
0 VDC
0 VDC
1776725469
2 Count
0 Count
0 Count
0 VDC
0 VDC
1776725123
1 Count
0 Count
0 Count
0 VDC
0 VDC
1776724979
0 Count
0 Count
0 Count
0 VDC
0 VDC
*Used Equation Coefficients:
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)