DO7BTR-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DO7BTR-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Temp*	Humi*	Baro*
1784653781	24 deg C	42.7 %	1023.7 hPa
1784651983	25.2 deg C	39.2 %	1023.9 hPa
1784649274	27.1 deg C	35.9 %	1024.1 hPa
1784648369	27.8 deg C	34.9 %	1024.2 hPa
1784646576	28.9 deg C	33.6 %	1024.3 hPa
1784576597	18.2 deg C	59.6 %	1023.7 hPa
1784575694	18.9 deg C	57.5 %	1023.7 hPa
1784574790	19 deg C	57.7 %	1023.6 hPa
1784573894	20 deg C	55.3 %	1023.7 hPa
1784572990	20.2 deg C	54.3 %	1023.6 hPa
1784572095	20.5 deg C	53.4 %	1023.7 hPa
1784571198	20.7 deg C	51.8 %	1023.7 hPa
1784570300	21.2 deg C	51.9 %	1023.6 hPa
1784569396	20.5 deg C	54.9 %	1023.6 hPa
1784568492	20.7 deg C	50.8 %	1023.6 hPa
1784567588	22.6 deg C	49.4 %	1023.6 hPa
1784566693	22 deg C	47 %	1023.6 hPa
1784565794	23.5 deg C	46.2 %	1023.7 hPa
1784564891	23 deg C	48.7 %	1023.7 hPa
1784563989	23.6 deg C	47.4 %	1023.5 hPa
1784563090	22.8 deg C	47.2 %	1023.5 hPa
1784562195	23.4 deg C	47.6 %	1023.4 hPa
1784561293	24.3 deg C	45.9 %	1023.4 hPa
1784560396	25.4 deg C	39.8 %	1023.5 hPa
1784559494	26.2 deg C	40.4 %	1023.4 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)