This is the latest recevied telemetry packets stored in our database for station/object DL1KDA-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
TX*
RX*
Digi*
V_Bat*
V_Ext*
1776852830
0 Count
0 Count
0 Count
0 VDC
0 VDC
1776852582
0 Count
0 Count
0 Count
0 VDC
0 VDC
1776840054
0 Count
0 Count
0 Count
0 VDC
0 VDC
1776838970
0 Count
0 Count
0 Count
0 VDC
0 VDC
1776837170
0 Count
0 Count
0 Count
0 VDC
0 VDC
1776835370
0 Count
0 Count
0 Count
0 VDC
0 VDC
1776833570
0 Count
0 Count
0 Count
0 VDC
0 VDC
1776831770
0 Count
0 Count
0 Count
0 VDC
0 VDC
1776829970
0 Count
0 Count
0 Count
0 VDC
0 VDC
1776828170
0 Count
0 Count
0 Count
0 VDC
0 VDC
1776826370
0 Count
0 Count
0 Count
0 VDC
0 VDC
1776824570
0 Count
0 Count
0 Count
0 VDC
0 VDC
1776820970
0 Count
0 Count
0 Count
0 VDC
0 VDC
1776819170
0 Count
0 Count
0 Count
0 VDC
0 VDC
1776817370
0 Count
0 Count
0 Count
0 VDC
0 VDC
1776815570
0 Count
0 Count
0 Count
0 VDC
0 VDC
1776813770
0 Count
0 Count
0 Count
0 VDC
0 VDC
1776811970
0 Count
0 Count
0 Count
0 VDC
0 VDC
1776811850
0 Count
0 Count
0 Count
0 VDC
0 VDC
*Used Equation Coefficients:
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)