This is the latest recevied telemetry packets stored in our database for station/object DF1IAN-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
Celsius*
Atm_Press*
Value3*
Value4*
Value5*
1784624969
41.2 deg C
1019.13 %
0
0
0
1784465097
28.4 deg C
1015.13 %
0
0
0
1784464742
28.2 deg C
1014.5 %
0
0
0
1784464536
28 deg C
1011.38 %
0
0
0
1784464262
28 deg C
1014.88 %
0
0
0
1784461483
27 deg C
1013.63 %
0
0
0
1784460279
27.6 deg C
1014 %
0
0
0
1784457729
26.5 deg C
1013.75 %
0
0
0
1784457501
26.3 deg C
1014.63 %
0
0
0
1784456672
25.5 deg C
1013.25 %
0
0
0
1784456330
25 deg C
1014 %
0
0
0
1784455969
24.6 deg C
1011.63 %
0
0
0
1784455736
24.5 deg C
1026.75 %
0
0
0
1784384602
35.4 deg C
1005.63 %
0
0
0
1784383847
35.5 deg C
1005.5 %
0
0
0
1784383630
35.5 deg C
1006.63 %
0
0
0
1784381352
34.1 deg C
1005.13 %
0
0
0
1784380720
34.3 deg C
1004.75 %
0
0
0
1784379255
33.7 deg C
1005.25 %
0
0
0
1784378670
33.3 deg C
1005.25 %
0
0
0
1784372601
29 deg C
1004.25 %
0
0
0
1784371516
28.4 deg C
1005.25 %
0
0
0
1783848203
33.8 deg C
1023.63 %
0
0
0
*Used Equation Coefficients:
Celsius: 0, 0.1, -50
Atm_Press: 0, 0.125, 0
Value3: 0, 1, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)