DG0OPK-95 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DG0OPK-95. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp.in*	Hum*	Temp.out*
1778072602	30.1 C deg	26.4 %	0 C deg
1778070747	30.1 C deg	26.4 %	0 C deg
1778069702	30.1 C deg	26.5 %	0 C deg
1778068966	30.1 C deg	26.5 %	0 C deg
1778067167	30 C deg	26.6 %	0 C deg
1778065360	30 C deg	26.6 %	0 C deg
1778065309	30 C deg	26.6 %	0 C deg
1778063503	29.9 C deg	26.8 %	0 C deg
1778061762	29.9 C deg	26.8 %	0 C deg
1778060674	29.8 C deg	27 %	0 C deg
1778060023	29.8 C deg	27 %	0 C deg
1778058139	29.7 C deg	27.1 %	0 C deg
1778058069	29.7 C deg	27.1 %	0 C deg
1778056239	29.6 C deg	27.4 %	0 C deg
1778055325	29.6 C deg	27.6 %	0 C deg
1778054412	29.6 C deg	27.6 %	0 C deg
1778053104	29.5 C deg	27.8 %	0 C deg
1778052628	29.5 C deg	27.8 %	0 C deg
1778050816	29.3 C deg	28.4 %	0 C deg
1778050806	29.3 C deg	28.4 %	0 C deg
1778048997	28.8 C deg	29.4 %	0 C deg
1778047316	28.2 C deg	30.5 %	0 C deg
1778047167	28.2 C deg	30.5 %	0 C deg
1778045422	29.9 C deg	25.8 %	0 C deg
1778045354	29.9 C deg	25.8 %	0 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)