KE0QIB Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KE0QIB. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1784693339	13.73 Volt	30 Pkt	68 Pcnt
1784693039	13.73 Volt	30 Pkt	69 Pcnt
1784692739	13.73 Volt	30 Pkt	68 Pcnt
1784692439	13.73 Volt	30 Pkt	69 Pcnt
1784692139	13.73 Volt	30 Pkt	67 Pcnt
1784691839	13.73 Volt	30 Pkt	72 Pcnt
1784691539	13.73 Volt	30 Pkt	70 Pcnt
1784691239	13.73 Volt	30 Pkt	71 Pcnt
1784690940	13.73 Volt	30 Pkt	69 Pcnt
1784690640	13.73 Volt	30 Pkt	69 Pcnt
1784690340	13.73 Volt	30 Pkt	66 Pcnt
1784690040	13.73 Volt	30 Pkt	68 Pcnt
1784689740	13.73 Volt	30 Pkt	68 Pcnt
1784689440	13.73 Volt	30 Pkt	69 Pcnt
1784689140	13.73 Volt	30 Pkt	67 Pcnt
1784688839	13.73 Volt	30 Pkt	70 Pcnt
1784688540	13.73 Volt	30 Pkt	71 Pcnt
1784688240	13.73 Volt	30 Pkt	70 Pcnt
1784687940	13.73 Volt	30 Pkt	71 Pcnt
1784687640	13.73 Volt	30 Pkt	73 Pcnt
1784687340	13.73 Volt	30 Pkt	74 Pcnt
1784687040	13.73 Volt	30 Pkt	74 Pcnt
1784686740	13.73 Volt	20 Pkt	75 Pcnt
1784686440	13.73 Volt	30 Pkt	79 Pcnt
1784686140	13.73 Volt	30 Pkt	76 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)