SR6ACZ-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR6ACZ-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	VBat*	Temp*	Wilg*	Cisn*
1784714392	12.92 V	18.5 C	58 %	990 hPa
1784711654	13.09 V	17.7 C	58 %	990 hPa
1784710741	13.1 V	17.3 C	58 %	990 hPa
1784709829	13.03 V	16.9 C	58 %	990 hPa
1784708916	12.95 V	16.5 C	59 %	990 hPa
1784708003	12.89 V	16.1 C	60 %	991 hPa
1784707093	12.83 V	15.8 C	60 %	991 hPa
1784705265	12.75 V	15.4 C	60 %	991 hPa
1784704353	12.74 V	15.2 C	61 %	991 hPa
1784703442	12.71 V	15.1 C	61 %	991 hPa
1784702527	12.72 V	14.9 C	61 %	991 hPa
1784701615	12.71 V	14.9 C	61 %	991 hPa
1784700702	12.71 V	14.9 C	61 %	991 hPa
1784699789	12.7 V	14.8 C	61 %	991 hPa
1784698877	12.71 V	14.8 C	60 %	991 hPa
1784697964	12.71 V	14.8 C	61 %	991 hPa
1784697054	12.71 V	14.8 C	60 %	991 hPa
1784696141	12.71 V	14.8 C	60 %	991 hPa
1784695232	12.7 V	14.9 C	60 %	991 hPa
1784694314	12.7 V	15 C	60 %	991 hPa
1784693402	12.71 V	15.1 C	60 %	991 hPa
1784691576	12.7 V	15.4 C	60 %	991 hPa
1784690662	12.7 V	15.5 C	60 %	991 hPa
1784689751	12.7 V	15.6 C	60 %	991 hPa
1784688837	12.71 V	15.6 C	60 %	991 hPa

*Used Equation Coefficients:

VBat: 0, 0.01, 0

Temp: 0, 0.1, 0

Wilg: 0, 1, 0

Cisn: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)