SQ3KT-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ3KT-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	V_Bat*
1784710414	350 Count	474 Count	4.32 VDC
1784709223	349 Count	473 Count	4.29 VDC
1784708012	348 Count	472 Count	4.33 VDC
1784706812	347 Count	471 Count	4.27 VDC
1784705611	346 Count	470 Count	4.31 VDC
1784704410	345 Count	469 Count	4.28 VDC
1784703209	344 Count	468 Count	4.33 VDC
1784702009	343 Count	467 Count	4.27 VDC
1784700808	342 Count	466 Count	4.27 VDC
1784699607	341 Count	465 Count	4.32 VDC
1784698406	340 Count	464 Count	4.3 VDC
1784697206	339 Count	463 Count	4.3 VDC
1784696005	338 Count	462 Count	4.26 VDC
1784694804	337 Count	461 Count	4.3 VDC
1784693603	336 Count	460 Count	4.33 VDC
1784692403	335 Count	459 Count	4.31 VDC
1784691202	334 Count	458 Count	4.28 VDC
1784690001	333 Count	452 Count	4.32 VDC
1784688812	332 Count	451 Count	4.28 VDC
1784687611	331 Count	450 Count	4.29 VDC
1784686411	330 Count	449 Count	4.28 VDC
1784685210	329 Count	448 Count	4.25 VDC
1784684009	328 Count	447 Count	4.26 VDC
1784682809	327 Count	446 Count	4.3 VDC
1784681608	326 Count	445 Count	4.27 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)