YD1BPG-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YD1BPG-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Temp.*	Humidity*	Pressure*
1789937068	32 °C	38 %RH	922 hPa
1789935093	32 °C	37 %RH	922 hPa
1789933118	32 °C	38 %RH	922 hPa
1789931143	32 °C	37 %RH	922 hPa
1789929168	33 °C	38 %RH	922 hPa
1789927193	33 °C	40 %RH	922 hPa
1789925218	33 °C	40 %RH	923 hPa
1789923243	33 °C	41 %RH	923 hPa
1789921268	33 °C	41 %RH	923 hPa
1789919293	34 °C	41 %RH	923 hPa
1789917318	34 °C	40 %RH	923 hPa
1789915343	34 °C	40 %RH	923 hPa
1789913368	34 °C	40 %RH	923 hPa
1789911392	34 °C	39 %RH	923 hPa
1789909418	35 °C	38 %RH	923 hPa
1789907442	35 °C	36 %RH	922 hPa
1789905468	35 °C	36 %RH	921 hPa
1789903492	34 °C	37 %RH	921 hPa
1789901517	35 °C	36 %RH	921 hPa
1789899543	35 °C	35 %RH	920 hPa
1789895592	35 °C	34 %RH	920 hPa
1789893617	34 °C	35 %RH	920 hPa
1789891642	34 °C	35 %RH	919 hPa
1789889667	34 °C	36 %RH	920 hPa
1789887692	33 °C	36 %RH	920 hPa

*Used Equation Coefficients:

Temp.: 0, 1, 0

Humidity: 0, 1, 0

Pressure: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)