CR7BYS-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object CR7BYS-13. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	CPU*	RAM*
1784702904	49 degC	0.8 %	90 %
1784702003	49 degC	0.7 %	90 %
1784701103	49 degC	0.5 %	90 %
1784700203	49 degC	0.5 %	90 %
1784699303	49 degC	0.6 %	90 %
1784698403	49 degC	0.5 %	91 %
1784697503	49 degC	0.6 %	89 %
1784696603	49 degC	0.6 %	91 %
1784695703	49 degC	0.6 %	91 %
1784694803	49 degC	0.7 %	90 %
1784693903	49 degC	0.6 %	90 %
1784693003	49 degC	0.5 %	90 %
1784692103	49 degC	0.7 %	90 %
1784691203	49 degC	0.7 %	90 %
1784690303	49 degC	0.6 %	90 %
1784689403	49 degC	0.8 %	90 %
1784688503	49 degC	0.7 %	90 %
1784687603	49 degC	0.6 %	90 %
1784686703	49 degC	0.5 %	90 %
1784685803	49 degC	0.6 %	90 %
1784684903	50 degC	0.6 %	89 %
1784684003	49 degC	0.7 %	89 %
1784683103	49 degC	0.6 %	90 %
1784682203	50 degC	0.6 %	89 %
1784681303	49 degC	0.6 %	90 %

*Used Equation Coefficients:

Temp: 0, 1, 0

CPU: 0, 0.1, 0

RAM: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)