F4EBW-7 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object F4EBW-7. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Celsius*	Rel_Hum*	Atm_Press*
1787559141	24.9 C	42.8 %	1013.88 hPa
1787550116	24.3 C	42.74 %	1012.5 hPa
1787541091	25.1 C	40.98 %	1014.38 hPa
1787532066	25.3 C	40.74 %	1014.5 hPa
1787523041	25.6 C	40.73 %	1016.5 hPa
1787514016	25.7 C	41.67 %	1017 hPa
1787504991	25.5 C	42.16 %	1016.88 hPa
1787495966	25.3 C	42.59 %	1018.13 hPa
1787486941	24.7 C	41.99 %	1019.38 hPa
1787477916	24 C	41.54 %	1020.13 hPa
1787468891	23.7 C	41.04 %	1019.88 hPa
1787459866	24 C	40.61 %	1020.25 hPa
1787450841	24.3 C	41.56 %	1020.88 hPa
1787441816	24.4 C	42.01 %	1021.38 hPa
1787432791	24.5 C	42.6 %	1021 hPa
1787423766	24.7 C	43.09 %	1020.5 hPa
1787414741	24.4 C	44.27 %	1019.5 hPa
1787396691	22.3 C	47.17 %	1021.25 hPa
1787387666	20.8 C	49.81 %	1021.63 hPa
1787378641	21.5 C	43.8 %	1021.13 hPa
1787369616	22.2 C	42.83 %	1021.25 hPa
1787360591	23.4 C	42.83 %	1019.63 hPa
1787351566	24.4 C	42.58 %	1019.13 hPa
1787342541	25.4 C	42.84 %	1019 hPa
1787333516	25.8 C	40.52 %	1015.38 hPa

*Used Equation Coefficients:

Celsius: 0, 0.1, -50

Rel_Hum: 0, 0.01, 0

Atm_Press: 0, 0.125, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)