IZ3ARR-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IZ3ARR-13. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vbat*	RSSI*	Uptime*
1781396007	3602 mV	-38 dBm	470 min
1781395407	3608 mV	-25 dBm	460 min
1781394807	3630 mV	-37 dBm	450 min
1781394208	3615 mV	-52 dBm	440 min
1781393608	3640 mV	-27 dBm	430 min
1781393008	3649 mV	-34 dBm	420 min
1781392407	3677 mV	-41 dBm	410 min
1781391807	3679 mV	-41 dBm	400 min
1781391208	3681 mV	-40 dBm	390 min
1781390607	3683 mV	-39 dBm	380 min
1781390007	3690 mV	-38 dBm	370 min
1781389408	3693 mV	-41 dBm	360 min
1781388808	3705 mV	-39 dBm	350 min
1781388207	3717 mV	-41 dBm	340 min
1781387607	3720 mV	-27 dBm	330 min
1781387007	3733 mV	-40 dBm	320 min
1781386407	3741 mV	-40 dBm	310 min
1781385807	3763 mV	-40 dBm	300 min
1781385208	3777 mV	-40 dBm	290 min
1781384608	3808 mV	-41 dBm	280 min
1781384007	3821 mV	-39 dBm	270 min
1781383407	3826 mV	-40 dBm	260 min
1781382807	3842 mV	-39 dBm	250 min
1781382207	3864 mV	-28 dBm	240 min
1781381608	3870 mV	-35 dBm	230 min

*Used Equation Coefficients:

Vbat: 0, 1, 0

RSSI: 0, 1, -100

Uptime: 0, 1, 0

Sat: 0, 1, 0

Rsvd: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)