DB0FTS-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB0FTS-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp.in*	Hum*	Temp.out*
1784684572	30.7 C deg	19 %	0 C deg
1784681077	30.8 C deg	18.6 %	0 C deg
1784679203	30.9 C deg	18.7 %	0 C deg
1784677377	30.8 C deg	18.7 %	0 C deg
1784672086	30.8 C deg	19 %	0 C deg
1784668250	30.9 C deg	19.4 %	0 C deg
1784666457	30.8 C deg	19.3 %	0 C deg
1784664658	31 C deg	19.9 %	0 C deg
1784662915	31 C deg	19.9 %	0 C deg
1784659183	30.9 C deg	18.8 %	0 C deg
1784657378	30.8 C deg	18.8 %	0 C deg
1784653755	30.7 C deg	21 %	0 C deg
1784650497	30.6 C deg	21.9 %	0 C deg
1784648537	30.5 C deg	21.8 %	0 C deg
1784646513	30.4 C deg	21.6 %	0 C deg
1784644663	30.6 C deg	21.1 %	0 C deg
1784642942	30.6 C deg	21.6 %	0 C deg
1784641073	30.7 C deg	21.6 %	0 C deg
1784639352	30.7 C deg	21.6 %	0 C deg
1784637397	30.5 C deg	21.6 %	0 C deg
1784635690	30.6 C deg	21.7 %	0 C deg
1784633906	30.5 C deg	21.8 %	0 C deg
1784632114	30.6 C deg	21.8 %	0 C deg
1784630230	30.6 C deg	21.8 %	0 C deg
1784628549	30.7 C deg	22.1 %	0 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)