KQ6DI-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KQ6DI-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Value1*	Value2*	Value3*	Value4*	Value5*
1784694669	14.81	-223.2	128.13	1	34
1784693759	14.81	-223.2	128.13	1	34
1784692849	14.81	-223.2	128.13	1	34
1784691939	14.81	-223.2	128.13	1	34
1784691049	14.81	-222.8	128.13	1	34
1784690119	14.81	-223.2	128.13	1	34
1784689209	14.81	-223.2	128.13	1	34
1784688299	14.81	-223.2	128.13	1	34
1784687389	14.81	-223.2	128.13	1	34
1784686479	14.81	-223.2	128.13	1	34
1784685569	14.81	-223.2	128.13	1	34
1784684659	14.81	-223.2	128.75	1	34
1784683749	14.81	-223.2	128.75	1	34
1784682839	14.81	-223.2	129.38	1	34
1784681929	14.81	-223.2	131.88	1	34
1784681019	14.81	-223.2	134.38	1	34
1784680109	14.81	-222.8	134.38	1	34
1784679199	14.81	-223.2	133.75	1	34
1784678289	14.81	-223.2	133.75	1	34
1784677379	14.81	-223.2	133.75	1	34
1784676469	14.81	-223.2	134.38	1	34
1784675559	14.81	-223.2	134.38	1	34
1784674649	14.81	-223.2	133.75	1	34
1784673739	14.81	-223.2	133.75	1	34
1784672829	14.81	-223.2	134.38	1	34

*Used Equation Coefficients:

Value1: 0, -0.0644, 15

Value2: 0, -0.4, -190

Value3: 0, 0.625, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)