SA0CBP-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SA0CBP-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	TX*	RX*	Digi*	V_Bat*	V_Ext*
1780587202	20 Count	0 Count	0 Count	0 VDC	0 VDC
1780586301	19 Count	0 Count	0 Count	0 VDC	0 VDC
1780585401	18 Count	0 Count	0 Count	0 VDC	0 VDC
1780584499	17 Count	0 Count	0 Count	0 VDC	0 VDC
1780583598	16 Count	0 Count	0 Count	0 VDC	0 VDC
1780582781	15 Count	0 Count	0 Count	0 VDC	0 VDC
1780582662	14 Count	0 Count	0 Count	0 VDC	0 VDC
1780582378	13 Count	0 Count	0 Count	0 VDC	0 VDC
1780581477	12 Count	0 Count	0 Count	0 VDC	0 VDC
1780580419	11 Count	0 Count	0 Count	0 VDC	0 VDC
1780537677	10 Count	0 Count	0 Count	0 VDC	0 VDC
1780537496	9 Count	0 Count	0 Count	0 VDC	0 VDC
1780536497	8 Count	0 Count	0 Count	0 VDC	0 VDC
1780535597	7 Count	0 Count	0 Count	0 VDC	0 VDC
1780534696	6 Count	0 Count	0 Count	0 VDC	0 VDC
1780534517	5 Count	0 Count	0 Count	0 VDC	0 VDC
1780534352	4 Count	0 Count	0 Count	0 VDC	0 VDC
1780534328	3 Count	0 Count	0 Count	0 VDC	0 VDC
1780534283	2 Count	0 Count	0 Count	0 VDC	0 VDC
1780534204	1 Count	0 Count	0 Count	0 VDC	0 VDC
1780534075	0 Count	0 Count	0 Count	0 VDC	0 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)