OE3FJB-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE3FJB-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Press*	Temp.in*	Hum*	QNH*	Temp.out*
1780848319	964.3 hPa	27 C deg	41.6 %	1066.4 hPa	0 C deg
1780841916	965.1 hPa	22.8 C deg	73.4 %	1023.3 hPa	0 C deg
1780841676	964.5 hPa	26.5 C deg	54.3 %	1021.9 hPa	0 C deg
1780841638	964.7 hPa	29.5 C deg	48.8 %	1021.5 hPa	0 C deg
1780840090	964.9 hPa	29.7 C deg	33.6 %	1021.7 hPa	0 C deg
1780840026	964.9 hPa	30.8 C deg	33.2 %	1021.5 hPa	0 C deg
1780839849	964.9 hPa	28.5 C deg	35.2 %	1022 hPa	0 C deg
1780839770	965 hPa	29.8 C deg	34.5 %	1021.8 hPa	0 C deg
1780839053	964.8 hPa	32 C deg	34 %	1021.2 hPa	0 C deg
1780838996	965 hPa	30.6 C deg	34.8 %	1021.6 hPa	0 C deg
1780838979	965 hPa	30.6 C deg	34.8 %	1021.6 hPa	0 C deg
1780838893	965 hPa	30 C deg	34.1 %	1021.7 hPa	0 C deg
1780838758	965 hPa	29.1 C deg	35.7 %	1021.9 hPa	0 C deg
1780838652	965.1 hPa	31.4 C deg	32.2 %	1021.5 hPa	0 C deg
1780838434	965 hPa	30.7 C deg	36.5 %	1021.6 hPa	0 C deg
1780838349	965.2 hPa	30.8 C deg	36.2 %	1021.7 hPa	0 C deg
1780837936	965 hPa	26.2 C deg	95.3 %	1022.5 hPa	0 C deg
1780837245	964.2 hPa	28.1 C deg	100 %	1021.2 hPa	0 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)