DB8ZP-99 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB8ZP-99. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp.in*	Hum*	Temp.out*
1785287923	34.7 C deg	23.9 %	24.6 C deg
1785280634	35.3 C deg	23.4 %	24.9 C deg
1785269746	36 C deg	22.5 %	25.9 C deg
1785267928	36.1 C deg	22.1 %	26 C deg
1785266113	36.1 C deg	21.2 %	26.1 C deg
1785257039	36.4 C deg	21.2 %	26.4 C deg
1785253415	36 C deg	21 %	26.9 C deg
1785249776	35.9 C deg	21.3 %	27.2 C deg
1785240707	35.4 C deg	22 %	27.7 C deg
1785233452	34.7 C deg	23 %	27.6 C deg
1785231639	34.5 C deg	22.8 %	27.8 C deg
1785229813	34.3 C deg	23.8 %	26.8 C deg
1785226191	34.2 C deg	25.1 %	25.9 C deg
1785224372	34 C deg	25.3 %	25.5 C deg
1785220735	33.7 C deg	24.8 %	24.4 C deg
1785213477	33.3 C deg	24.7 %	23.2 C deg
1785209845	33.6 C deg	24.7 %	23.3 C deg
1785204402	33.9 C deg	25 %	23.8 C deg
1785198955	34.3 C deg	25 %	24.2 C deg
1785193510	34.7 C deg	24.7 %	24.5 C deg
1785191692	34.8 C deg	24.6 %	24.6 C deg
1785186249	35 C deg	24.5 %	24.8 C deg
1785182617	35.1 C deg	24.5 %	25.1 C deg
1785171727	35.4 C deg	24 %	25.7 C deg
1785166288	35.1 C deg	24.8 %	26.1 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)