HS8AS-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS8AS-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TEMP*	HUM*	VBAT *
1781424595	35.45 °C	53.3 %RH	4.19 V
1781423995	36.81 °C	52.4 %RH	4.19 V
1781423395	35.98 °C	51 %RH	4.19 V
1781422795	36.38 °C	51.6 %RH	4.18 V
1781422195	36.95 °C	51.6 %RH	4.18 V
1781421595	35.88 °C	52.2 %RH	4.18 V
1781420995	35.64 °C	51.2 %RH	4.19 V
1781420395	37.06 °C	49.6 %RH	4.19 V
1781419795	34.87 °C	53 %RH	4.18 V
1781419195	34.71 °C	58.9 %RH	4.17 V
1781418595	35.03 °C	55.7 %RH	4.15 V
1781417995	35.36 °C	52.1 %RH	4.17 V
1781417395	34.57 °C	58.8 %RH	4.17 V
1781416795	34.44 °C	57 %RH	3.99 V
1781416194	35.01 °C	57.5 %RH	3.98 V
1781415594	35.48 °C	56.2 %RH	4 V
1781415019	35.75 °C	53.7 %RH	4 V
1781414394	33.83 °C	56.9 %RH	4 V
1781413794	35.18 °C	59.1 %RH	4 V
1781413194	33.12 °C	62.3 %RH	4 V
1781412594	33.72 °C	59.1 %RH	4 V
1781411994	34.55 °C	56 %RH	4 V
1781411394	34.56 °C	54.7 %RH	4 V
1781410794	34.93 °C	58 %RH	4.01 V
1781410194	34.22 °C	59.4 %RH	3.99 V

*Used Equation Coefficients:

TEMP: 0, 0.01, 0

HUM: 0, 0.1, 0

VBAT : 0, 0.01, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)