ER-PI1DFT Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ER-PI1DFT. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Value1*	Value2*	Value3*	Value4*
1784674595	0 RX Erlang	0.01 TX Erlang	0 RXcount/10m	1 TXcount/10m
1784673995	0 RX Erlang	0.01 TX Erlang	1 RXcount/10m	2 TXcount/10m
1784673395	0 RX Erlang	0 TX Erlang	0 RXcount/10m	0 TXcount/10m
1784672795	0 RX Erlang	0.02 TX Erlang	1 RXcount/10m	2 TXcount/10m
1784672195	0 RX Erlang	0.01 TX Erlang	2 RXcount/10m	2 TXcount/10m
1784671595	0 RX Erlang	0.01 TX Erlang	0 RXcount/10m	1 TXcount/10m
1784670995	0 RX Erlang	0.01 TX Erlang	0 RXcount/10m	1 TXcount/10m
1784670395	0 RX Erlang	0.01 TX Erlang	0 RXcount/10m	1 TXcount/10m
1784669795	0 RX Erlang	0.01 TX Erlang	0 RXcount/10m	1 TXcount/10m
1784669195	0 RX Erlang	0.02 TX Erlang	2 RXcount/10m	1 TXcount/10m
1784668595	0.02 RX Erlang	0.04 TX Erlang	3 RXcount/10m	2 TXcount/10m
1784667995	0.02 RX Erlang	0.04 TX Erlang	2 RXcount/10m	3 TXcount/10m
1784667395	0 RX Erlang	0.01 TX Erlang	0 RXcount/10m	1 TXcount/10m
1784666795	0 RX Erlang	0.02 TX Erlang	1 RXcount/10m	1 TXcount/10m
1784666195	0.18 RX Erlang	0.31 TX Erlang	36 RXcount/10m	16 TXcount/10m

*Used Equation Coefficients:

Value1: 0, 1, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)