DL0ALT-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DL0ALT-12. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	ATemp*	AHum*	vRate*	Sats*	Alt*
1789901264	48.4	14.7	0	7	79.8
1789900958	48.8	14.2	0	7	77.1
1789900805	48.9	14.1	0	7	77.5
1789897274	46.4	18.1	0	12	81.9
1789896659	45.6	19.5	0	11	80.3
1789896505	45.3	19.8	0	12	80.4
1789894970	28.2	53.8	0	11	81.7
1789894839	24.4	58.5	0	11	76.1
1789894664	21.9	59.7	0	11	75.9
1789894583	21.3	58.1	0	0	0
1789894503	21	56.1	0	0	0
1789591320	44.7	22.9	0	8	83.1
1789590553	42.3	28.7	0	9	79.2
1789589631	32.4	51.2	-0.1	8	74.7
1789589171	24.4	65.1	0	8	79
1789498878	37.5	29.9	0.1	8	90.2
1789498111	37.5	30.7	-0.1	11	81.4
1789496884	37.5	33.2	-0.1	8	83.7
1789496576	36.6	35.8	0.1	10	98.1
1789496268	34.8	39.5	-0.1	8	69.8
1789495961	31.8	46.1	0	9	86.8
1789495420	25.6	59.7	0	0	0
1789491010	22.6	62.2	0	12	77.8
1789490089	23	60.8	0	12	79
1789489782	23.3	60.5	0	12	83.2

*Used Equation Coefficients:

ATemp: 0, 1, 0

AHum: 0, 1, 0

vRate: 0, 1, 0

Sats: 0, 1, 0

Alt: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)