KZ4EU-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KZ4EU-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RFIn*	RFiGate*	DigiRpt*	Temp*
1781534182	76 Pkts	74 Pkts	60 Pkts	17 C
1781530582	70 Pkts	69 Pkts	51 Pkts	17 C
1781526982	85 Pkts	84 Pkts	49 Pkts	17 C
1781523382	33 Pkts	32 Pkts	19 Pkts	17 C
1781519782	37 Pkts	35 Pkts	12 Pkts	17 C
1781516182	31 Pkts	30 Pkts	19 Pkts	17 C
1781512582	22 Pkts	22 Pkts	17 Pkts	17 C
1781508982	22 Pkts	21 Pkts	19 Pkts	17 C
1781505382	30 Pkts	28 Pkts	20 Pkts	17 C
1781501782	62 Pkts	60 Pkts	24 Pkts	17 C
1781498182	88 Pkts	86 Pkts	25 Pkts	17 C
1781494582	41 Pkts	41 Pkts	21 Pkts	16 C
1781490982	75 Pkts	74 Pkts	24 Pkts	16 C
1781487382	99 Pkts	97 Pkts	29 Pkts	16 C
1781483784	118 Pkts	116 Pkts	30 Pkts	16 C
1781480182	100 Pkts	98 Pkts	27 Pkts	18 C
1781476582	98 Pkts	96 Pkts	31 Pkts	18 C
1781472982	138 Pkts	136 Pkts	47 Pkts	19 C
1781469382	139 Pkts	135 Pkts	46 Pkts	17 C
1781465782	88 Pkts	86 Pkts	33 Pkts	16 C
1781462182	12 Pkts	11 Pkts	7 Pkts	16 C

*Used Equation Coefficients:

RFIn: 0, 1, 0

RFiGate: 0, 1, 0

DigiRpt: 0, 1, 0

Temp: 0, 1, 0

InetiGate: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)