MTVVPC Telemetry

This is the latest recevied telemetry packets stored in our database for station/object MTVVPC. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	SOC*	Capacity*	Voltage*	Current*	Temp*
1784662007	100 %	100 Ah	54 V	0 A	25 C
1784660809	100 %	100 Ah	54 V	0 A	25 C
1784656607	100 %	100 Ah	54 V	0 A	25 C
1784653609	100 %	100 Ah	54 V	0 A	25 C
1784651809	100 %	100 Ah	54 V	0 A	25 C
1784651207	100 %	100 Ah	54 V	0 A	25 C
1784650009	99 %	99 Ah	52 V	5 A	25 C
1784649406	97 %	97 Ah	51 V	5 A	25 C
1784648806	97 %	97 Ah	51 V	5 A	25 C
1784648208	97 %	97 Ah	51 V	6 A	25 C
1784645806	97 %	97 Ah	50 V	0 A	25 C
1784644608	97 %	97 Ah	50 V	0 A	25 C
1784644006	97 %	97 Ah	50 V	0 A	25 C
1784643406	97 %	97 Ah	50 V	0 A	25 C
1784642808	97 %	97 Ah	50 V	0 A	25 C
1784642206	97 %	97 Ah	50 V	0 A	25 C
1784641606	97 %	97 Ah	50 V	0 A	25 C
1784641008	97 %	97 Ah	50 V	0 A	25 C
1784640406	97 %	97 Ah	50 V	0 A	25 C
1784639806	98 %	98 Ah	50 V	-1 A	25 C
1784639208	98 %	98 Ah	50 V	-1 A	25 C
1784638606	98 %	98 Ah	50 V	-1 A	25 C
1784638006	98 %	98 Ah	50 V	0 A	25 C
1784637408	98 %	98 Ah	50 V	0 A	25 C
1784636806	98 %	98 Ah	50 V	0 A	25 C

*Used Equation Coefficients:

SOC: 0, 1, 0

Capacity: 0, 1, 0

Voltage: 0, 1, 0

Current: 0, 1, -128

Temp: 0, 1, -40

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)