DG7RJ-8 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DG7RJ-8. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp.in*	Hum*	Temp.out*
1788573298	28 C deg	45.4 %	0 C deg
1788571467	28 C deg	45.4 %	0 C deg
1788569637	28 C deg	45.4 %	0 C deg
1788567807	28.1 C deg	45.2 %	0 C deg
1788565977	28.1 C deg	45 %	0 C deg
1788564147	28.2 C deg	45.2 %	0 C deg
1788562317	28.3 C deg	45 %	0 C deg
1788560487	28.3 C deg	45 %	0 C deg
1788558656	28.4 C deg	45.1 %	0 C deg
1788556826	28.5 C deg	45.1 %	0 C deg
1788554996	28.6 C deg	45.5 %	0 C deg
1788553166	28.6 C deg	45.4 %	0 C deg
1788551336	28.4 C deg	45.9 %	0 C deg
1788549506	28.3 C deg	46 %	0 C deg
1788547676	28.2 C deg	44.6 %	0 C deg
1788545846	28.2 C deg	44.2 %	0 C deg
1788544016	28.3 C deg	43.9 %	0 C deg
1788542185	28.4 C deg	43.7 %	0 C deg
1788540355	28.4 C deg	43.4 %	0 C deg
1788538525	28.2 C deg	43.8 %	0 C deg
1788536695	28.2 C deg	45.9 %	0 C deg
1788534865	27.9 C deg	44.5 %	0 C deg
1788533035	28 C deg	44.6 %	0 C deg
1788531205	27.9 C deg	44.9 %	0 C deg
1788529375	27.9 C deg	45.4 %	0 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)