KNKTRL Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KNKTRL. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1787564310	13.2 Volt	240 Pkt	30 Pkt	93 Pcnt
1787564010	13.28 Volt	240 Pkt	30 Pkt	93 Pcnt
1787563711	13.28 Volt	230 Pkt	30 Pkt	93 Pcnt
1787563710	13.28 Volt	230 Pkt	30 Pkt	93 Pcnt
1787563410	13.28 Volt	240 Pkt	30 Pkt	93 Pcnt
1787563110	13.28 Volt	240 Pkt	30 Pkt	93 Pcnt
1787562810	13.28 Volt	230 Pkt	30 Pkt	92 Pcnt
1787562510	13.28 Volt	240 Pkt	30 Pkt	92 Pcnt
1787562210	13.28 Volt	240 Pkt	30 Pkt	91 Pcnt
1787561910	13.28 Volt	240 Pkt	30 Pkt	92 Pcnt
1787561610	13.28 Volt	240 Pkt	30 Pkt	91 Pcnt
1787561310	13.28 Volt	250 Pkt	30 Pkt	91 Pcnt
1787561010	13.28 Volt	240 Pkt	30 Pkt	91 Pcnt
1787560711	13.28 Volt	240 Pkt	30 Pkt	92 Pcnt
1787560710	13.28 Volt	240 Pkt	30 Pkt	92 Pcnt
1787560410	13.28 Volt	240 Pkt	30 Pkt	89 Pcnt
1787560111	13.28 Volt	230 Pkt	30 Pkt	89 Pcnt
1787560110	13.28 Volt	230 Pkt	30 Pkt	89 Pcnt
1787559810	13.28 Volt	230 Pkt	30 Pkt	89 Pcnt
1787559511	13.28 Volt	220 Pkt	30 Pkt	88 Pcnt
1787559510	13.28 Volt	220 Pkt	30 Pkt	88 Pcnt
1787559210	13.28 Volt	230 Pkt	30 Pkt	89 Pcnt
1787558911	13.28 Volt	230 Pkt	30 Pkt	89 Pcnt
1787558910	13.28 Volt	230 Pkt	30 Pkt	89 Pcnt
1787558610	13.28 Volt	230 Pkt	30 Pkt	89 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)