SR9POD-0 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9POD-0. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Vin*	T_in*	Rx1h*	Dg1h*
1789939209	13.65 Volt	24.5 C	200 Pkt	20 Pkt
1789938609	13.65 Volt	25 C	200 Pkt	20 Pkt
1789936809	13.65 Volt	25 C	150 Pkt	10 Pkt
1789935010	13.65 Volt	25.5 C	160 Pkt	10 Pkt
1789933809	13.65 Volt	25.5 C	200 Pkt	10 Pkt
1789843811	13.65 Volt	24.5 C	150 Pkt	0 Pkt
1789834811	13.65 Volt	28 C	360 Pkt	180 Pkt
1789833614	13.65 Volt	28.5 C	340 Pkt	170 Pkt
1789831812	13.65 Volt	29 C	440 Pkt	220 Pkt
1789831211	13.65 Volt	29 C	450 Pkt	220 Pkt
1789829432	13.65 Volt	29 C	450 Pkt	210 Pkt
1789828813	13.65 Volt	29 C	440 Pkt	200 Pkt
1789827612	13.65 Volt	29 C	390 Pkt	180 Pkt
1789826416	13.65 Volt	28.5 C	370 Pkt	140 Pkt
1789820412	13.73 Volt	29 C	390 Pkt	50 Pkt
1789809011	13.65 Volt	28 C	490 Pkt	120 Pkt
1789803014	13.65 Volt	24.5 C	330 Pkt	40 Pkt
1789748417	13.65 Volt	27.5 C	290 Pkt	70 Pkt
1789739413	13.73 Volt	29.5 C	160 Pkt	10 Pkt
1789717213	13.65 Volt	23.5 C	210 Pkt	10 Pkt
1789670416	13.65 Volt	23 C	170 Pkt	20 Pkt
1789665615	13.65 Volt	24 C	200 Pkt	30 Pkt
1789663814	13.65 Volt	24.5 C	200 Pkt	30 Pkt
1789635015	13.65 Volt	24 C	270 Pkt	20 Pkt
1789590616	13.65 Volt	26.5 C	140 Pkt	20 Pkt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

T_in: 0, 0.5, -64

T_out: 0, 1, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)