SHLDR Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SHLDR. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Temp*	Temp*
1785343856	13.65 Volt	16 C	-62 C
1785341756	13.8 Volt	15.5 C	-62 C
1785339656	14.4 Volt	15.5 C	-62 C
1785337556	14.4 Volt	15 C	-62 C
1785335456	14.4 Volt	14.5 C	-62 C
1785333357	13.43 Volt	14 C	-62 C
1785331256	12.68 Volt	14.5 C	-62 C
1785329156	12.6 Volt	14.5 C	-62 C
1785327056	12.68 Volt	15 C	-62 C
1785324957	12.68 Volt	15 C	-62 C
1785322857	12.68 Volt	15.5 C	-62 C
1785320757	12.68 Volt	16 C	-62 C
1785318657	12.68 Volt	16 C	-62 C
1785316557	12.75 Volt	16.5 C	-62 C
1785314457	12.75 Volt	17 C	-62 C
1785312357	12.75 Volt	17.5 C	-62 C
1785310260	12.75 Volt	18 C	-62 C
1785308159	12.75 Volt	18.5 C	-62 C
1785306057	12.75 Volt	19 C	-62 C
1785303957	12.75 Volt	19.5 C	-62 C
1785301857	12.83 Volt	20 C	-62 C
1785299757	12.83 Volt	20.5 C	-62 C
1785297658	13.13 Volt	21 C	-62 C
1785295557	13.58 Volt	21.5 C	-62 C
1785293457	13.65 Volt	21.5 C	-62 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Temp: 0, 0.5, -67

Temp: 0, 0.5, -62

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)