SR9WXL-0 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9WXL-0. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Tx10min*	Digi10min*
1789965152	63 Pkt	3 Pkt	0 Pkt
1789962745	76 Pkt	4 Pkt	0 Pkt
1789960941	59 Pkt	3 Pkt	0 Pkt
1789956117	45 Pkt	2 Pkt	0 Pkt
1789954914	73 Pkt	3 Pkt	0 Pkt
1789954313	52 Pkt	3 Pkt	0 Pkt
1789951907	54 Pkt	4 Pkt	0 Pkt
1789950701	56 Pkt	4 Pkt	0 Pkt
1789950099	49 Pkt	2 Pkt	0 Pkt
1789949498	79 Pkt	3 Pkt	0 Pkt
1789948896	45 Pkt	7 Pkt	0 Pkt
1789947082	59 Pkt	3 Pkt	0 Pkt
1789945880	76 Pkt	4 Pkt	0 Pkt
1789945275	58 Pkt	2 Pkt	0 Pkt
1789942871	41 Pkt	3 Pkt	0 Pkt
1789941066	41 Pkt	3 Pkt	0 Pkt
1789933234	51 Pkt	2 Pkt	0 Pkt
1789929014	57 Pkt	3 Pkt	0 Pkt
1789927812	76 Pkt	4 Pkt	0 Pkt
1789844704	45 Pkt	2 Pkt	0 Pkt
1789841094	74 Pkt	9 Pkt	2 Pkt
1789838078	73 Pkt	7 Pkt	3 Pkt
1789836271	63 Pkt	2 Pkt	0 Pkt
1789834466	77 Pkt	3 Pkt	0 Pkt
1789833865	49 Pkt	3 Pkt	0 Pkt

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

HostTx10m: 0, 1, 0

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)